PLUMBING 101: TIPS FOR INSTALLING A BATHTUB

Plumbing 101: Tips for Installing a Bathtub

Plumbing 101: Tips for Installing a Bathtub

Blog Article

Call Us Today

Just how do you feel on the subject of Tools You Need to Install a New Bathtub ?


A Step-by-Step Guide to Installing a Bathtub
Setting up a bathtub isn't exactly rocket science, yet it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a new one is likewise a reasonably tough job. If the old bathtub is easily available, the task can move speedily; if you have to open up a wall surface to eliminate the old tub and position the brand-new tub, the job is much harder. In either case, the job is within a house handyman's skills, although you will require an assistant to vacate the old tub and embeded in the brand-new one. Make sure you have actually qualified on your own for the job as well as are comfortable attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is better to consider using one before you begin. Opportunities are you may need an expert plumber to make tube links.
This article will assist you mount a new tub in your bathroom if you have actually currently gotten a brand-new tub and do not need to transform the plan of your previous water supply pipes.
Your devices and material checklist must make up the following:
  • New Bathtub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps


  • Planning for the Installation


    Firstly, the sustaining framework supplied with the bath must be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the taps system to stop pressure on the tub.
    Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
    Link the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final position.

    Removing Old Touches


    If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, turn on the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome as a result of the restricted gain access to that is often the situation.
    Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a towel all set for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have actually been gotten rid of, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning during this process. When the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
    Before proceeding to fit the brand-new taps, contrast the pipeline connections on the old taps to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the new faucets to fit.

    Setting up the Bathtub


    Using both wood boards under its feet, position the bathtub in the required setting. The wooden boards are practical in evenly spreading out the weight of the tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
    The following goal is to make certain that the tub is leveled all round. This can be achieved by examining the level and adjusting the feet on the bath tub until the spirit level reviews level.
    To set up taps, fit all-time low of the outermost versatile faucet adapter to the suitable supply pipe by making a compression sign up with; then do the same for the other tap.
    Switch on the water supply and also examine all joints and new pipework for leaks as well as tighten them if needed. Load the tub as well as additionally inspect the overflow outlet and also the normal outlet for leaks.
    Ultimately, fix the bathroom paneling as described in the supplier's instruction manual. Tiling and sealing around the bath tub must wait until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last setting.

    Suitable New Taps


    If the tails of the new taps are plastic, then you will certainly need a plastic port to avoid damage to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
    If you need to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next off, place the tap in the placing opening in the bath/basin making certain that the washing machines are in area between the faucet and also the sink. Protect the faucet in place with the supplier offered backnut. When the tap is securely in place, the supply pipes can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind should be attached to the tap finishes first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.

    Tiling Around the Tub


    In the area where the bathroom satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to fracture a rigid seal, triggering the water to permeate the wall in between the bathroom and the tiling, bring about difficulties with dampness and feasible leakages to the ceiling listed below.
    You can choose from a variety of coloured sealants to blend in your components and also fittings. They are marketed in tubes and cartridges, and also can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the tub with water prior to sealing, to permit the activity experienced when the bathtub is in use. The sealant can crack rather very early if you do not take into account this activity prior to securing.
    Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the tiles using waterproof or water-proof adhesive and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    A Step-by-Step Guide to Installing a Bathtub

    I am just very enthusiastic about How to Install a Bathtub Yourself and I really hope you liked the entry. So long as you appreciated our blog entry kindly remember to pass it around. Thanks a lot for your time spent reading it.


    Contact our experts.

    Report this page